Questions tagged [power]
The power tag has no usage guidance.
13
questions
5
votes
1
answer
74
views
What battery/motor setup will replace this 1980s vintage glow engine?
I have a sport model (RCM Terrier, balsa/plywood construction covered with Monokote or Econokote stick/shrink film) that I built in 1984, and it has somehow come through multiple moves apparently ...
- 282
4
votes
2
answers
413
views
How to limit the power of the brushless motor
I need to limit the power of my brushless motor at 700 Watts. How I can do it?
I dont have a fix motor or propeller, for any configuration the max consumed power need to be less or equal 700W.
The max ...
- 318
4
votes
2
answers
174
views
FC powers RX only if USB is connected?
this is my first UAV build, so please don't bare with me :)
I use basically a S500 frame with 4S setup and a flightstack using a Holybro Kakute F7 1.5 FC, connected with a Holybro Tekko32 4in1 ESC ...
- 235
4
votes
0
answers
199
views
How to power a Companion Computer using the Holybro Pixhawk 4 Power Module (PM07)?
As the title says, I would like to power a companion computer (Raspberry Pi 3B in my case) using the PM07 Power Distribution Module: Power Module
The Raspberry Pi should be powered via USB cable.
...
- 81
3
votes
1
answer
371
views
ESC overload protection at stall current?
I am trying to build, for the first time a drone, on a F330 frame, 30a ESC and 1000KV 2212 motors... But I destroyed 2 ESCs in the process. It literally burned up when the drone falled and the ...
- 183
1
vote
1
answer
53
views
Can be ESC connected to battery directly if PDB has not enough power?
I want to use FC Matek F405-TE http://www.mateksys.com/?portfolio=f405-te#tab-id-4 but it's PDB allow only 35A of ESC. I want to use 50-60A ESCs (motors are 40A each) with this controller.
Can I ...
- 187
1
vote
1
answer
39
views
How do I store a Li-ion pouch battery without any discharger or balancer?
I have a single-cell 3.7V 900 mAh Li-ion pouch battery and a 7.4V 30c 2s 850Mah Li-ion pouch battery. I want to store these two batteries (the manufacturer suggests I should store the 2s pack at 3.8V)....
- 55
1
vote
1
answer
389
views
What battery can I use for 1000kv brushless motor, that will be the cheapest?
I am using a 10 x 4.5 propeller for my A2212/13T 1000KV brushless motor with a 30A ESC. What battery will I need that will be cheap to power my motor alongside three 9-gram servos?
Flight time is not ...
- 55
1
vote
1
answer
148
views
I have a design for powering four motors, could someone verify that it will work as I planned?
My question:
This is a simple design that I have created using everything that I know about electronics so far. Is there anything missing in my design or are there any concepts which I have ...
- 25
1
vote
1
answer
200
views
Radius of drone when hovering in circles
According to Energy Minimization for Wireless Communication With Rotary-Wing UAV, it is better to fly in circles than to hover at a single place (if hovering is required). Flight requires less power. ...
- 153
0
votes
1
answer
69
views
Can I put lipo and li-ion batteries in series
I have two 3.7 volt 900 mAh LiPo battery, which I connected in series to provide 7.4 volts. But now I want 11.1 volts.
Instead of buying another LiPo battery, am I able to put these two LiPo batteries ...
- 55
0
votes
1
answer
17
views
Flight properties vs Energy Storage, is it a linear relationship?
I found an interesting drone platform from the brand: Dji Drones.
From the spec sheet found here, I realized it had some limitations... but was curious if were to modify by adding more batteries, ...
- 101
0
votes
1
answer
198
views
How can I use a Pixhawk 4 power distribution board (PM07) to power an older pixhawk?
I have the PM07 power distribution board designed for the Pixhawk 4 but I currently have a Pixhawk 2.8.4. On the data sheets I can clearly see a 5V output but I am not getting any power from those ...
- 43