Questions tagged [compatibility]

Use in questions asking about how two or more UAV-related things can be used together.

Filter by
Sorted by
Tagged with
3 votes
1 answer
319 views

Does the Mavic Mini 2 drone support the DJI FPV controller and goggles?

The drone: Official Website | Where I'm buying it from I am looking for a drone for a class at school, but we need one under 250 grams, and that supports First Person View, so that we can use VR ...
user avatar
  • 33
2 votes
1 answer
45 views

Do I need anything else for this drone build?

So far, I have these parts as all I need for a drone build. Is there anything else that I need or should have? Flight controller: DJI Naza-M Lite TX/RX: FS-i6 Drone body: F450 Motors: 2212 920kv ...
user avatar
  • 303
5 votes
1 answer
52 views

For a typical dual controller + companion computer UAS, is it normal to have UART only from controller, and USB only from companion computer?

When I'm reading the extension capability of 3DR Solo, I realise that its breakout board interface has some peculiar limitation. Here is the context of the entire 3DR Solo design: it is an open-source,...
user avatar
  • 153
5 votes
2 answers
77 views

Brushless Upgrade for RC Car

I was told that if my question was about motors and ESCs than it would be okay to put it on here even though it has to do with an RC car... I am wanting to do a brushless upgrade for my WLTOYS 12428 ...
user avatar
3 votes
1 answer
84 views

Does the FS-R6B receiver work with the JJPRO EM-16 transmitter?

If I need a new receiver and can't find one that is exactly the same as the one that came with the radio, can I get one with the same amount of channels and from the same company and use it with the ...
user avatar
3 votes
1 answer
390 views

Specs of the XT30 port on DJI M600 PRO

I'm new here and so I would appreciate any answers, I work in a research laboratory at Brazil and we have an M600 PRO. I need to connect some components to the XT 30 port, so I need to know more ...
user avatar
1 vote
1 answer
125 views

What type of connector is used on the DJI manifold 2?

I'm looking for a certain connector's specification that is used in the DJI Manifold 2. Unfortunately, there is no information about this connector's specifications in the data sheet, it only talks ...
user avatar
7 votes
1 answer
322 views

Possible to use Eachine E160 with Futaba T6EX transmitter/receiver set?

I've inherited a Futaba T6EX transmitter with a Futaba R6106HFC receiver, and now I'm planning to buy an Eachine E160 RC helicopter (BNF version), to be bound to this Futaba set. However, I'm not sure ...
user avatar
5 votes
2 answers
622 views

Will this set up fry my components?

Frame: Carbon fiber 250mm Motors: 2300Kv 2204 Power board: Matek built in BEC’s 12V + 5V FC: CC3D ESCs: HLGRC 30A opto (no BEC) Battery: Turnigy Graphene 14V 75C 4S Receiver: Turnigy iA6B My question ...
user avatar
  • 51
3 votes
3 answers
129 views

How to program drones that have old flight controllers?

I have a few components of drones like some old FCs and old ESCs and I don't want them to go to waste. Is there any way to configure a drone that I built with those parts, as I don't think the FCs are ...
user avatar
  • 5,510
2 votes
1 answer
457 views

Why don't multiprotocol transmitters work with Radiolink receivers?

I have a Jumper T16 and am wondering why it or any other multiprotocol transmitters don't work with Radiolink receivers. Is there a reason for this?
user avatar
  • 5,510